03
Apr
You will notice a groove around fuel connections which indicate a left-handed thread. The oxygen regulator is model 250-80-540 by National Welders.
The acetylene is by Craftsweld Equipment Corp.
Oxygen and acetylene gauges. ZenStyle Oxygen Acetylene Gas Cutting Torch and Welding Kit Portable Oxy Brazing Welder Tool Set with Two HoseRegulator GaugesStorage Case. 43 out of 5 stars. The best oxygen-acetylene torch comes with two separate gauges one for the oxygen tank and one for the fuel tank.
The best brazing kit will also come with a torch of course where the fuel and air will mix. A torch should have multiple nozzles for different jobs. Also make sure you also have a decent case to include and store all your accessories.
Oxy-Acetylene gas cutting supplies and equipment for sale at ieDepot. In stock and available for same day dispatch across Ireland. The acetylene inside the acetylene cylinder is an extremely volatile and combustible gas.
Since oxygen itself is a combustion-supporting gas when acetylene is mixed with oxidant to react and heat it will cause an explosion. The oxygen cylinder is a compressed gas cylinder with high purity and high-pressure oxygen. Close both torch valves.
For the oxygen turn the pressure-adjusting screw on the regulator until the gauge reads about 25 psi. For the acetylene turn the pressure-adjusting screw on the regulator until the gauge reads about 10 psi. It is very important to test for leaks before starting your project.
Up for bid is a used Oxygen Acetylene Welding Tank Regulator Valves Gauges. The oxygen regulator is model 250-80-540 by National Welders. The acetylene is by Craftsweld Equipment Corp.
Have not used for awhile but worked fine when put away any questions please ask thank you. Oxy Acetylene Welding Set Up and Pressure Settings Chart. The first we must Clean the nozzle because if the head of the nozzle dirty will cause flame bad.
Open Regulator Oxygen and Acetylene set until the pressure matching with what do you want or for acetylene 5 to 7 psi and Oxygen 7 to 10 psi. The third open valve in the torch first. Answer 1 of 3.
Acetyline should never be higher than 15 PSI past the regulator. Oxegen should be set to whatever your task needs. Cutting torch needs more pressure than a welding torch.
Niether tank pressure should be allowed to go below 25 PSI. Acetyline pressures over 15PSI can auto ignite a. HARRIS 601 OXYGENACETYLENE TORCH GAUGES.
HOSES REGULATORS- CUTTINGWELDING Hello. Welcome to our auction. Gauges and hoses are in great condition.
The tank side oxygen gauge is missing. Check photos for details please. Please contact with any questions before bidding.
Our items are described as accurately as possible. Use gauges designed for a specific gas for a different gas. Never use an oxygen gauge for acetylene.
From one gas application to another. DO NOT Exchange gauges from one regulator to another. DO NOT Remove the restrictor installed in the gauge connection.
The restrictor limits gas flow and aids in. SÜA - Oxygen and Acetylene Regulators Welding Gas Gauges - Rear Entry - LDP. Cylinder to Regulator Acetylene Adaptors.
Oxygen and acetylene regulators used at stations to which gases are piped from an oxygen manifold acetylene manifold or acetylene generator have only one low pressure gauge because the pipe line pressures are usually set at 15 psi 1034 kPa for acetylene and approximately 200 psi 1379 kPa for oxygen. Oxygen regulators have right-hand threads and regulators for Acetylene and other fuel gases have left-hand threads. You will notice a groove around fuel connections which indicate a left-handed thread.
Finally all outlet low pressure gauges on Acetylene regulators have their gauge scales marked in red starting at 15 psig. How to set the oxy acetylene regulators Im going to tell you how to set the pressure regulators and probably get into torch tips and a few things like that for oxy-acetylene. Its very important how you set these things.
You know the high pressure and the oxidizing problem with oxygen if theres any carbon present. The acetylene cant be over 30 pounds. Gauges for use with acetylene can also be used in welding applications.
Gauges with brass case are cleaned to meet ASME B401 Level IV for oxygen service. Gauges with 304 stainless steel case are cleaned and bagged to meet ASME B401 Level IV for oxygen service. For technical drawings and 3-D models click on a part number.
Additionally why Acetylene is used in gas welding. Acetylene produces a flame temperature of 3100 degree Celsius along with oxygen. This high flame temperature makes acetylene a suitable choice for gas welding steel.
When burned in oxygen acetylene produces a reducing zone which easily cleans the metal surface. Turn the valve of the oxygen tank or cylinder until it is fully open. Locate the regulators adjusting screw and turn it clockwise until the gauge shows that the pressure being released is between 40 to 60 psi.
For the acetylene cylinder do a counterclockwise turn for the valve but only a quarter of the way. Adjust acetylene to form feather shaped flame. Continue to add oxygen until neutral flame is established.
If there is too much acetylene flame breaks away from the tip. Oxygen can be 99 pure and makes things burn really fast. Acetylene Cylinders These cylinders have lower amounts of pressure in them but can be quite dangerous because acetylene is a fuel and can easily ignite.
As a safety measure acetylene should never be released or used at a rate above 15 pounds per square inch psi. 1 product rating - HARRIS MODEL 601-15-200 400 PSI GAUGE ACETYLENE REGULATOR 601-15-300 HAR 9006256. Oxygen and Acetylene Gauge Oxygen and Acetylene Gauge Pressure Gauges products of Pressure Gauges offered by Koang Yee Enterprise Co Ltd.